Fastest: call (833) 490-5225. Or send this and we call you back.
Extraction & Pumping
Flood Water Extraction and Pumping: what it covers
Quick answer
Extraction is the first physical step in any flood job in Indianapolis: pumps remove standing water, then wet vacuums and extractors take the film left on floors and carpet. Indianapolis Water Damage Restoration answers 24/7 and dispatches a crew as fast as one is available. Drying starts only after the water is out.
Nothing dries while it is still under water. That sounds obvious, but it is the reason extraction comes first, and why a fan set up in a flooded basement does very little until the pumps have run. In Indianapolis the water in a basement might come from the White River, from a creek, from a drain that backed up or from a pipe, and the pumping approach is similar for each, though the safety rules are not.
Extraction has two parts. Pumps handle depth: water that stands inches or feet deep. Extractors and wet vacuums handle what is left, the film on a slab, the water in carpet and pad, the pools in low corners. The work is quick compared with drying, but it is the step that stops further damage, because water left standing keeps climbing into drywall and wood.
Phones at Indianapolis Water Damage Restoration are answered 24/7, and a crew is dispatched as fast as one is available. Tell the dispatcher how deep the water is, whether the power is on in that area, and whether you can see the source. The answers decide the equipment on the truck.
Do not step into standing water while the power is on, and never plug a pump or vacuum into an outlet that is wet or below the waterline. Do not empty a deep basement all at once.
Water above the level of the floor drain that is not draining
A basement stair where the bottom steps are under water
Carpet that looks wet from the doorway and sounds wet underfoot
A garage floor with a film of water that returns after it is swept
Pooled water around a water heater or furnace base
A strong damp smell from a closed room
Rising water that continues after rain has stopped
A sump pit that is full and not cycling
Our process
How our flood water extraction and pumping visit works
Assess depth, source and power
The technician measures the depth, looks for the entry point and checks whether the electrical panel or outlets are in the water. If the answer is unsafe, the electric supply to the area is dealt with before pumps go in.
Choose the pump
A submersible pump handles clear water, and a trash pump handles water that carries silt and debris. The discharge hose runs to a place where the water will not flow back toward the house.
Lower the level in stages
In a below-grade space the crew often drops the water in steps and checks the walls between each one. Soil outside may still be full of water, and a sudden empty basement can put pressure on walls and floor.
Extract the remainder
After the pumps run out of depth, extractors lift the film from slab and carpet. Pad is often lifted and removed; carpet may be kept if it was clean water and the pad can be replaced.
Move to drying
Once the floor is clear, readings are taken and air movers and dehumidifiers go in. The extraction log, with start and finish times, becomes part of the record.
Why does water have to come out before drying starts?
Dehumidifiers and air movers remove moisture from air and surfaces, not bulk water. If the floor is covered, the equipment spends its capacity on water that a pump could move in minutes. Extraction first shortens the drying period and limits how far the water climbs.
Walls, baseboards and carpet pad are porous, and they pull water upward by wicking. The longer water stays in contact, the higher it goes and the more material has to be opened up. That is the practical case for fast pumping.
Once the bulk water is gone, the job becomes a measurement exercise. Meters read the moisture in each material, and the crew drives those readings down. The structural drying and dehumidification page covers that stage.
Can I pump a flooded basement myself?
A homeowner can safely pump only when the power is off, the water source has stopped and the level is lowered gradually. The risks are electrical shock, a collapsed wall from rapid pressure change, and contaminated water. For deep or dirty water, a crew is the safer route.
The pressure issue is one reason professionals lower a basement in stages. When the soil outside holds water and the inside is emptied at once, the difference can push on a wall or lift a slab.
If you have a small amount of clean water from a pipe, a wet vacuum is reasonable, provided the outlet is on a protected circuit and not in the water. When in doubt, call before you plug anything in.
Where does the pumped water go in Indianapolis?
The crew runs the discharge away from the foundation to a spot that can take it, and keeps contaminated water out of storm drains where rules require. Clean water from a pipe and flood water from a river are not discharged the same way.
Indianapolis has combined sewers in older areas, and pumping water into a street drain during a storm can add to the load on the system. The crew picks the discharge point with that in mind.
Citizens Energy's DigIndy tunnel network was built to reduce combined sewer overflow, and by late 2018 the company reported more than 500 million gallons kept out of the White River and Eagle Creek. It is a reminder that the sewer system in the city is under strain in heavy rain.
What equipment is used for extraction?
Submersible pumps for depth, trash pumps for silty water, wet vacuums for edges and extractors for carpet and flooring. A moisture meter then confirms what remains. The mix depends on how deep the water is and what it carried.
Truck-mounted units can pull water from carpet quickly, and portable extractors reach rooms the truck cannot. Carpet pad is often pulled out rather than extracted, because it holds water and is cheap to replace compared with the subfloor under it.
Hardwood and engineered floors need special handling, and the crew may use mats that draw water from the boards. Whether a wood floor can be saved depends on how long it was wet.
Options
Types and options for flood water extraction and pumping
Deep standing water in a basement
A foot or more of water calls for submersible pumps and a hose run to an exit point. It can also call for care about what is stored below the line, since boxes and furniture float and shift. The pace is set by the walls, not by the pump.
Shallow water across a finished floor
A few inches of water on a finished floor looks harmless, but it wicks into baseboards and the bottom of walls quickly. Extractors work fast here, and the crew follows up with a moisture map before deciding what to remove.
Contaminated or silt-laden water
River, creek and sewage water cannot be handled like a leak. The crew uses a pump that tolerates solids, wears protective equipment and disposes of the water as the situation requires. See the sewer backup cleanup page for the sewage case.
Marion County
Why flood water extraction and pumping is different in Central Indiana
Indianapolis sits where the White River, Fall Creek, Pleasant Run and Eagle Creek all drain through the city, so the source of a flooded basement varies from one part of town to another. A house near the river may take overbank water, while one on high ground may fill from a drain.
The city's older areas still use combined sewers, which can overflow with as little as a quarter inch of rain. When the sewer is full, pumping water from a basement to the street makes no sense, and the crew plans the discharge accordingly.
A large share of Indianapolis housing has a basement, and many of those basements are the older kind with a poured wall and a single floor drain. A crew finds the drain, tests it and notes whether it is moving water before the pumps are set.
Skip the guesswork. Call for a straight answer.
Tell us what's happening and we'll tell you honestly whether it's a quick fix, and what flood water extraction and pumping should cost.
Drying starts with getting the water out, not with fans.
Read the guide
FAQ
Flood Water Extraction and Pumping FAQs
How quickly can a crew start pumping?
A crew is dispatched as fast as one is available once your call is answered. We do not promise an arrival time, because it depends on the crews free at that moment and the roads.
Do you pump clean water and flood water the same way?
The pumps are similar, but the protective equipment, disposal and cleaning that follow are not. Contaminated water gets the stricter procedure.
Can I keep my carpet after extraction?
Sometimes. If the water was clean and the carpet was wet for a short time, it may be dried in place with the pad replaced. Flood or sewage water usually means carpet and pad go.
What if my sump pump is running constantly?
That may mean groundwater is high or the pump is overworked. The sump pump failure page explains what to check.
Will pumping stop mold?
It is the first step. Mold needs moisture over time, and removing standing water and then drying the structure removes that condition.
Do I need to move my belongings first?
Move what you can safely lift to dry surfaces, photograph the rest, and let the crew handle the heavy items.