Conventional drying
Air movers and dehumidifiers with the room closed. This is the usual method for carpet, wall bottoms and slab, and it works well when the wet area is open and accessible.
Wet walls, floors and subfloors are dried with air movers and dehumidifiers, and meters confirm when the drying is finished.
Fastest: call (833) 490-5225. Or send this and we call you back.
Structural drying removes moisture that remains in framing, subfloors, slabs and wall cavities after the visible water is gone. In Indianapolis, Indianapolis Water Damage Restoration sets air movers and dehumidifiers, takes meter readings on each visit, and keeps equipment running until the readings match a dry reference. Phones are answered 24/7.
A floor that looks dry is not necessarily dry. Water that has been in a house for a day or more soaks into studs, plates, subfloor, plaster and the back of drywall, and it leaves slowly. Structural drying is the stage that deals with that hidden moisture, and it is the stage that decides whether a house returns to normal or grows mold behind a fresh coat of paint.
The method is simple in outline and exacting in practice. Air movers push dry air across wet surfaces so water evaporates, and dehumidifiers pull that moisture out of the air so the room does not just fill with humidity. A technician places moisture meters on the framing and slab, writes down a reading, and comes back to check it.
In Indianapolis the work is shaped by the housing and the weather. Many homes are older brick and frame with basements, and the year includes humid summers and cold, dry winters, so the equipment setting and the room closure change by season. Phones at Indianapolis Water Damage Restoration are answered 24/7, and a crew is dispatched as fast as one is available.
Do not move or unplug drying equipment without asking, since it may be balanced on a circuit. Keep children and pets away from hoses, cords and hot exhaust from dehumidifiers.
The technician scans walls and floors with a moisture meter, and may use a thermal camera to find cool, wet patches. The map shows where the water went, which is often further than the visible stain.
Readings are taken from an unaffected wall or floor of the same material. That number becomes the dry target. Without it, there is no way to say drying is complete.
Air movers go on wet floors and walls at angles that push air across the surface. Dehumidifiers are sized to the space and the amount of water. In some cases, wall cavities are opened or drilled so air can reach inside.
The crew returns to check readings, move equipment and adjust. Humidity in the room is tracked as well, because a dehumidifier working against a leaking room does not do its job.
When readings match the reference, the equipment comes out. You receive a log of the readings from first visit to last.
Water leaves dense materials slowly. Studs, plates, concrete and plaster hold moisture inside, and evaporation only works from the surface. Equipment speeds that process, but it cannot skip it. The time depends on the material, the amount of water and the room conditions.
Drywall dries faster than concrete, and thin paneling faster than a thick sill plate. A basement slab may take the longest because it is cool and sits against damp soil.
The crew sets a goal by reading unaffected materials, then checks progress. If readings stall, it changes the equipment placement or opens a wall.
They compare readings on the wet materials with readings on the same materials in an unaffected part of the house. When the two match within the target, drying is done. The log of readings is the proof, and you should receive a copy.
A hand on the wall is not a test. Moisture meters read electrical resistance or other signals in the material, and they catch water that cannot be felt.
If a crew cannot show you readings, ask for them. The record is also what a repair contractor and an insurer will want.
Humid summers slow evaporation, so dehumidifiers matter more. Cold winters keep indoor air dry but can make slabs cool, which slows drying from below. The January mean of about 28.5 F also means the heating system affects how fast a house dries.
In summer, open windows can bring in humid air and make drying worse. A closed room with a dehumidifier is the usual setup. In winter, heat helps, and a house kept at a normal temperature dries faster than a cold one.
Snowmelt and rain at the foundation can keep a basement damp from the outside. If the wall keeps getting wet, drying will not hold, and the cause has to be fixed.
It can if materials stay wet for long enough. Fast extraction and drying are the best prevention. If mold is already present, the crew may need to follow a containment and removal approach described on the mold page before drying continues.
Mold needs moisture, food and time. Paper-faced drywall and dust on damp wood supply the food. The quicker the moisture is brought down, the less chance mold has.
The page on mold after water damage explains signs to watch for.
Each assembly dries differently. Masonry and slabs release moisture slowly from the surface, wood floors must be dried gently to avoid cupping or splitting, and framed walls dry fastest when a cavity is opened or ventilated. The crew picks equipment and pace for each assembly, not one setting for the house.
A slab or brick wall is dense and cool, and water leaves it by diffusing to the surface. Air movers help only at the surface, so the main tool is a dehumidifier holding room humidity low enough that the material keeps giving up water. It is slow, and readings often plateau before they fall again.
A wood floor is the delicate case. Boards swell as they take on water and shrink as they lose it, and drying too quickly can split or cup them. The crew may use drying mats, low airflow and steady monitoring, and decides after several visits whether the floor will flatten or be replaced.
In a framed wall the question is access. The bottom plate and the base of the studs are the wettest parts, and removing a baseboard or drilling small holes at the base lets air in. The homeowner sees small openings and ducted hoses, and a wall that stays closed until readings say otherwise.
Expect a steady roar from air movers, a warm room from dehumidifiers, cables on the floor and a technician returning on set visits with a meter. You may see small holes, lifted baseboards and taped plastic sheeting. All of it is temporary.
Dehumidifiers also put out heat and a stream of warm air, so a closed room can feel like a sauna, and the collected water is drained to a hose or tank. Do not open windows to relieve it unless the crew says so, since outside air in a humid Indiana summer works against the process.
Each visit the crew reads the same points, records them and moves machines. A falling trend is the good sign. A flat trend after a day or two means the crew changes something: more dehumidification, a cavity opened or a hidden source ruled in or out.
Air movers and dehumidifiers with the room closed. This is the usual method for carpet, wall bottoms and slab, and it works well when the wet area is open and accessible.
When water has gone into a wall or under cabinets, small holes or removed baseboards let air or injected dry air reach the cavity. The holes are small and are repaired in the rebuild.
Wood floors need controlled drying, since drying too fast can split boards. Mats and low-velocity air may be used, and the floor is monitored. Whether it can be saved depends on how long it stayed wet. The water heater leak damage page covers one common cause.
Indianapolis has a large stock of older brick and frame homes, many with basements and some with crawl spaces. The materials in them, including plaster, lath, old hardwood and masonry, dry differently from modern board and require individual readings.
The city's 1991-2020 normals show about 43.63 inches of precipitation and 25.5 inches of snow a year. A wet spring can leave a basement slab damp, and a drying job in that season has to account for the outside conditions.
Equipment placement is also affected by how a home is used. In an occupied house, the crew works around beds and kitchens, and noise and power draw are part of the plan. In a commercial space, see the commercial water restoration page.
Call any hour and explain what is going on. You get a clear price before any work starts.
Not sure if you're covered? Check your ZIP code.
Standing water comes out by pump and extractor first, because drying cannot start while the floor is still under water.
Mold that follows water is handled by stopping the moisture, containing the area and removing affected porous materials.
Wet ceilings and walls are opened and dried so water behind drywall is found, and what cannot be saved is removed.
Damp crawl spaces and shallow basements are measured, dried and documented so wood and insulation stop holding water.
An Indianapolis restoration quote follows how much area got wet, how long it stayed wet, whether the water was clean or contaminated, and which materials must come out.
Stay out of flood water until power is off and the structure is safe, document the damage, and treat river water as contaminated.
Many older Indianapolis neighborhoods are still served by combined sewers that carry storm water and sewage in one pipe, so heavy rain can push wastewater back into basements.
After heavy rain, work out where the water came from before you clean.
If a pipe has frozen and nothing has leaked yet, open the nearest tap, thaw it gently with warm air and leave the water on.
Drying starts with getting the water out, not with fans.
Ask for a written scope and terms before work starts, ask how moisture will be measured and recorded, and confirm who will deal with your insurer.
It depends on the materials and the amount of water. The crew checks readings on each visit and removes equipment when the structure reaches the dry target.
They make noise like large fans. Many people find them tolerable in the daytime and difficult at night. Tell the crew if sleep is an issue, since placement can sometimes be adjusted.
Yes, because the equipment draws power. The size of the change depends on how many machines run and for how long. Ask the crew what to expect and tell your insurer.
Household fans help a little with surface moisture but do not replace dehumidifiers. Humid air from household fans can spread moisture.
The crew looks for a hidden source or a closed cavity. Sometimes a wall needs to be opened.
Yes. Standing water is extracted before drying starts. See flood water extraction and pumping.