Tank failure
The tank corrodes through or a seam splits. The whole contents can empty over minutes to hours, and the water spreads across the basement.
A leaking tank floods the floor around it; the water is extracted, wet materials are removed and the area is dried.
Fastest: call (833) 490-5225. Or send this and we call you back.
A leaking or failed water heater can empty its tank onto a Indianapolis basement floor, and a slow leak can soak walls and flooring for weeks. Indianapolis Water Damage Restoration answers 24/7 and dispatches a crew as fast as one is available. We extract the water and dry the structure; a plumber replaces the tank.
A water heater holds dozens of gallons, and when the tank fails, that water goes straight to the floor. Many Indianapolis homes keep the heater in the basement, beside the furnace, the washer and boxes of stored items. That puts a lot of damageable property within reach of a puddle.
Leaks come in two forms. A sudden failure of the tank or a fitting releases water quickly and leaves a clear mess. A slow leak at a valve, a supply connection or a relief line seeps for weeks, and may only show up as a rusty stain, a soft wall or a smell.
Phones at Indianapolis Water Damage Restoration are answered 24/7, and a crew is dispatched as fast as one is available. If the heater is leaking, shut off its water supply and power, and call. A gas heater needs the gas valve turned off too, and if you smell gas you should leave and call the utility from outside.
Turn off gas or electric power to the heater before approaching, but do not do so while standing in water. If you smell gas, leave and call the utility from outside.
The heater is shut off at the electrical breaker or gas valve and its cold-water supply is closed. This prevents further damage and removes a shock hazard.
Pumps, wet vacuums and extractors clear the floor. If the heater sits near a floor drain, the crew checks that the drain is moving water.
Carpet pad, cardboard, wet insulation and the bottom of drywall that soaked up the water are removed when readings call for it. Items that can be dried are moved out.
Air movers and dehumidifiers run until meters match the dry reference. Because heater water is hot, check the readings in nearby framing, which can be warm and damp for a time.
The crew photographs the failure point and gives you the log. A plumber replaces or repairs the heater, and the report supports the claim.
Turn off the power or gas to the heater, close its cold-water supply valve, keep clear of the water, move belongings and call. If you smell gas, leave the building and call the utility from outside. Do not touch wet electrical equipment.
If the heater is electric and the floor is wet, do not reach for the breaker if you have to stand in water. Wait for help or find the panel from a dry spot.
Photograph the heater, the water and anything damaged before it is moved. Those pictures help in a claim.
It is supply water, so it starts clean, but it passes through sediment, rust and the contents of the basement floor. It is treated with normal care, and carpet and boxes that soaked in it are often removed.
Sediment inside a tank can give the water a rusty look, and it can stain flooring. The discoloration alone does not mean contamination, though it makes a mess of porous materials.
If the heater drain or relief line connects to a floor drain that backed up, the water may be mixed. See the sewer backup cleanup page.
No. A restoration crew dries the structure and removes wet materials. A plumber or water heater technician decides whether to repair or replace the unit, and handles gas, venting and electrical connections.
The crew can tell the plumber what it saw: where the water came from, what was wet and for how long.
Replacing a unit before the floor is dry is possible, but the floor needs checking, since a slow leak may have affected the slab edge or the wall base.
Many homeowners policies cover sudden leaks and bursts and exclude long-term seepage or wear. The tank itself is usually not covered. Read the policy, call the insurer and keep your records. This site does not state what any policy pays.
A sudden failure and a slow leak can be treated differently. The restoration record can show what the crew found, such as a rusty tide line suggesting a long-term seep.
See insurance claim documentation for what to keep.
The floor, the wall behind the tank, anything stored nearby and often the furnace cabinet. Heater water spreads in a wide sheet, so the footprint of the loss is usually larger than the puddle suggests. Meters show where the water went and what is still wet.
Basement heaters often share the same corner as the furnace, the electrical panel and shelves of stored boxes. Cardboard wicks water quickly and carries it up to what sits on top of it. Furnace cabinets and their controls are wet-sensitive, and a heating technician should check them before they run again.
Walls that are framed against a masonry foundation can trap water at the base plate, where air barely moves. The crew checks there on every heater call, since a wall can look fine from the room and still read wet at the bottom.
If the heater sits on a concrete slab with a floor drain, the water may have run to the drain and away. That reduces the standing water but not the damage to the bottom of walls, and the readings still decide the work.
It spreads across the slab in a sheet, soaks the base of every wall it touches and drains slowly toward the floor drain, if the slab slopes that way. The wall bottom plate and the stored items on the floor take the most damage, and a tank failure can wet a whole basement room.
A basement slab is rarely level. Water runs toward the low side, which may be the drain or a corner, and pools there. The crew follows the slope and checks the wall base along the whole path, not only beside the heater.
Hot water adds a wrinkle. Warm water enters materials more easily and leaves a warm, humid pocket in a closed corner, which is a good setting for early mold if it is not dried quickly. The crew reads warm spots in framing as well as wet ones.
The homeowner sees a flooded corner, then equipment placed across the room. Boxes, carpet remnants and cardboard are removed for the claim record; solid shelving and plastic bins are usually cleaned and kept.
For restoration, the water is the same. For safety, it matters a great deal. An electric unit is a shock hazard in standing water, and a gas unit adds a pilot, a vent and a gas line. Neither is reconnected or restarted by the restoration crew.
A gas heater that has been in standing water needs a qualified technician to inspect the burner, the gas valve and the venting before it runs again. An electric heater needs its wiring checked. The crew will tell you what it saw; the decision belongs to the plumber or heating technician.
If the heater shares a space with a furnace, the same goes for the furnace controls. Do not restart either unit until it has been checked.
The tank corrodes through or a seam splits. The whole contents can empty over minutes to hours, and the water spreads across the basement.
A supply line, shutoff or relief valve drips. The leak may be small enough to ignore for weeks, which means the damage is hidden behind a base or under a pan.
A heater on an upper floor or in a closet can send water through the floor below. See ceiling and drywall water damage for what happens when it comes through a ceiling.
A large share of Indianapolis housing has a basement, and that is where the water heater usually sits. Water lands on a slab that may have a single floor drain, and anything stored on the floor is at risk.
Older neighborhoods near the center have older houses, and an older house may have a heater installed decades after it was built, connected to old plumbing. The crew looks at the fittings as well as the tank.
Basements in the city also take water from other sources, such as storms and drains. If your basement has flooded before, the heater may be raised on a stand or set in a pan. The crew notes the setup in its record.
Tell us what's happening and we'll tell you honestly whether it's a quick fix, and what water heater leak damage should cost.
Not sure if you're covered? Check your ZIP code.
Leaks from washers, dishwashers and ice-maker lines wet floors and walls; the water is extracted and the floor assembly dried.
Standing water comes out by pump and extractor first, because drying cannot start while the floor is still under water.
Wet walls, floors and subfloors are dried with air movers and dehumidifiers, and meters confirm when the drying is finished.
Moisture meters and thermal imaging trace water behind walls and under floors, then the wet area is opened and dried.
A plumber handles that. The restoration crew focuses on the water that has already escaped.
That depends on the policy and the cause. Ask your insurer.
No. A small leak can soak a wall base and flooring over weeks. Call, and have it measured.
Sometimes, if the water was clean and quickly removed. Pad usually needs replacing.
Not if it is dried and wet materials are removed. A lingering smell suggests hidden moisture.
The crew takes care around hot water and steam, and the heater is shut off before work begins.